Installation package needed
Hello everyone, I'm trying to get a package where it contains the whole dependencies so i can install zenoss. My problem is that where my server is located has no access to the internet - so i need to...
View ArticleRe-assigning decommissioned device IP
Recently we needed to reassign one of the Decommissioned server's (Device-1) IP to an existing server (Device-2).While trying to reset the IP of Device-2, Zenoss 3.x was failing with the following...
View ArticleZenoss 4.2 Maps Portlet error "OVER_QUERY_LIMIT"
Having tried Zenoss and loving it i'm begining to fill it with routers i'm monitoring on the internet.Als goes well and there's lots of info when something doesnt work or when you don't no how.Great...
View ArticleGraphs Customization
Hello, We recently updated to the last version of zenoss to do some monitoring, we have some custom device for which we've created some graphs and they work fine.in zenoss 3.x there was a simple way...
View ArticleGoogle Maps Over Query Limit
I just added some more locations (32 total now) and I get the Over Query Limit at location number 30 every single time. I have tried clearing the geocache and I have also raised the timeout values in...
View ArticleGoogle Maps always geocodes
I am currently using Zenoss 4.2 on CentOS 64 bit. I have been attempting to display around 40 nodes (increasing in the future) in the Google Maps Portlet. My problem currently is that Zenoss wants to...
View Article"zenoss" user password
By mistake i changed "zenoss" user password. It does not seem to have any impact but i have not yet restarted zenoss. My questions: 1. will zenoss password change effect my system when i restart...
View ArticleZenping correlation problem 4.2.3
Hi all, sicne I have updated our zenoss form 3.2.1 to 4.2.3 layer3 correlation between devices doesn't work.When remote site goes down zenoss is sending several alerts insted of one for a router.For...
View ArticleHow to model network-interfaces without monitoring them?
Hi, is there any way to model network-interfaces (and get their ip, mac adress etc.) but not to poll their performancedata and interface states? greetings,christian
View ArticleUnauthorized: You are not allowed to access 'zProperty' in this context -...
Stuck on Zenoss 3.1.0 for now, lately my collectors have started failing to fetch zencommand and zenjmx config where these commands in data sources depend on a zProperty that is unchanged and inherited...
View Articlecan't start the zenhub
Hi everyone, I have make set up the zenoss 4.2.3 on the suse 11. Almost I can start all the daemons but the zenhub. I have found some problems about the ipv6. The error is following:...
View ArticleCalculated Performance data source
Hi All, Anybody had success in using Calculated Performance zenpack on 4.2.3 ? I got an error like below: Preparing Command...Executing command $ZENHOME/libexec/ against 10.0.0.1/bin/sh:...
View ArticleZenoss 4.2.3 UI Performance is almost unusable
I've had 4.2.3 installed for a couple weeks now. The UI performance has just been atrocious, before and after performing all documented tuning. It takes ~15 seconds to load the infrastructure page of...
View Article[ZC4.2SP1] zenjobs not running: celery.worker: permission denied
Hi all, We are having a problem on a new (clean) installation of Zenoss Core 4.2 with Service Pack 1 applied on a new (clean) machine with CentOS 6. The daemon zenjobs is not running. According to...
View ArticleUpgrade from 3.2.1 to 4.2.3 and RHEL 5 to RHEL 6
I am on a new project to upgrade our current version of Zenoss 3.2.1, & the operating system RHEL 5 to 4.2.3 & RHEL 6 respectively on a new vm using vmware. I am new to this at every level. I...
View Articlepage configuration in zenoss core 4
Hi, Do we have any document of how to configure page alerts in zenoss core 4.2.3 ? Regards,Arumon
View ArticlePerformance monitoring IBM Disk Storage DS5000
Hi Guys, I'm new to Zenoss, but I'm trying to find out a way to monitor the performance of my IBM's DS5020. I can pull some data from the DS with the IBM client command line: SMcli # ./SMcli...
View ArticleFirst steps with Zenoss and first problems - Graphs empty
Hi, I'am a new Zenoss user and I have some problems. I'm sorry if I do stupid questions but I have not found the solutions to my issues. Some details to explain the view of the situation:- Zenoss...
View ArticleZODB Database
Hi, I am new to Zenoss. i created a sample zenpack using ZenPack Development Guide- from wiki 20130309.pdf I came to know that for the newly added attributes , objects will be stored in ZODB by default...
View ArticleZenoss firefox search
Hey guys,I put together a Firefox search plugin for Zenoss. It requires you to manually place your zenoss hostname in the xml file but it works well:<SearchPlugin...
View Article